页岩油、兰炭、焦炭、电石、铁合金等炼化生产企业，在生产过程中会伴随产生大量的低热值工业尾气。这些可燃气体成分以氢气、一氧化碳为主，成分复杂、杂质多、成分不稳定、毒性大、易燃易爆，除小部分炼化工厂自用外，剩余大部分燃烧排空浪费。

Refining and chemical production enterprises such as shale oil, blue coke, coke, calcium carbide and ferroalloy will produce a large amount of low calorific value industrial tail gas in the production process. These combustible gases are mainly composed of hydrogen and carbon monoxide, with complex composition, many impurities, unstable composition, high toxicity, flammability and explosion. Except for the self-use of a small number of refining and chemical plants, most of the rest are burned and exhausted.

针对此类气体，以燃气内燃机为基础，开发了适用于焦炉煤气、发生炉煤气、兰炭尾气、油页岩尾气、电石尾气、铁合金尾气等多种工业尾气的大功率燃气发电机组，功率范围500-1200kW。将这些可燃焦炉煤气发电利用变废为宝, 既了排放对空气的污染，又可节约电力资源。

For this kind of gas, based on the gas internal combustion engine, a high-power gas generator unit with a power range of 500-1200kW has been developed, which is suitable for coke oven gas, producer gas, coke tail gas, oil shale tail gas, carbide tail gas, ferroalloy tail gas and other industrial tail gas. The utilization of these combustible coke oven gas for power generation can not only solve the air pollution caused by emissions, but also save power resources.

氢气、一氧化碳类燃气适应性强、适用范围广；

Hydrogen and carbon monoxide gas have strong adaptability and wide application range;      

对于炼化气中焦油、粉尘、硫、萘等杂质耐受性好；

Good resistance to impurities such as tar, dust, sulfur and naphthalene in refining gas;

空气与燃气缸内混合，高氢燃气无回火问题，性高；

Air is mixed with gas cylinder, high hydrogen gas has no flashback problem and high safety;      

空燃比自动调节，对燃气波动的适应性强，功率输出稳定；

Automatic adjustment of air-fuel ratio, strong adaptability to gas fluctuations, and stable power output;

自动化程度高，具备一键启动、自动合闸、加载等功能；

High degree of automation, with one-button start, automatic closing, loading and other functions;      

年运行时间长、故障率低、检修周期长、运行成本低;

Long annual operation time, low failure rate, long maintenance cycle and low operation cost;

应用气源要求

Application gas source requirements

燃气在进机前应经过除尘、除焦油、脱硫、脱水、冷却处理，达到以下要求：

The gas shall undergo dust removal, tar removal, desulfurization, dehydration and cooling before entering the machine, and meet the following requirements:

进机燃气温度≤40°C; 燃气热值≥4.0MJ/Nm3

Inlet gas temperature ≤ 40 ° C; Gas calorific value ≥ 4.0MJ/Nm3

燃气压力2.5~ 10kPa; 压力变化率≤1kPa/min;

Gas pressure 2.5~10kPa; Pressure change rate ≤ 1kPa/min;

水分含量≤40g/Nm3, 不含游离水; 粉尘含量≤30mg/Nm3;

Water content ≤ 40g/Nm3, without free water; Dust content ≤ 30mg/Nm3;

粉尘粒度≤5μm; 焦油含量≤50mg/Nm3;

Dust particle size ≤ 5 μ m; Tar content ≤ 50mg/Nm3;

硫化氢含量≤50mg/Nm3; 硫总含量≤100mg/Nm3;

Hydrogen sulfide content ≤ 50mg/Nm3; Total sulfur content ≤ 100mg/Nm3;

氨含量≤20mg/Nm3 苯含量≤50mg/Nm3

Ammonia content ≤ 20mg/Nm3 Benzene content ≤ 50mg/Nm3

萘含量≤50% 氢气体积含量≤60%

Naphthalene content ≤ 50% Hydrogen volume content ≤ 60%

含氢气体氧气体积含量≤1%

Hydrogen containing gas, oxygen volume content ≤ 1%